fundingferro.blogg.se - Homelite super xl automatic carburter

#HOMELITE SUPER XL AUTOMATIC CARBURTER HOW TO#
#HOMELITE SUPER XL AUTOMATIC CARBURTER PDF#

HJ-HJ INLET OIL PUMP LINE 1!1-1!1 OUTLET OIL PUMP FITTING TO GUIDE BAR PAD FITTING. HANDGUARD KIT DECAL- Handguard WASHER- Curve spring WASHER- Flat SCREW- Shoulder ~ġ 1 1 1 4 1 4 'f 1 1 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 6 1 1 1 1 1 1 1 1 1 1 1 1įIGURE 2 FIGURE 2 ABBILDUNG 2 FIGURA 2 FIGURA 2 FILTER GRIP- Starter SCREW- Torx, plastite (#10 X 3/4') SPRING & CONTAINER ROPE- Starter PULLEY- Starter WASHER- Retaining SWITCH LEAD- w/Fiag Term.

(#1 0-24 X 3/4') PRIMER BULB TUBING- Inlet (3') TUBING- Return (7') PLATE- Guide bar WASHER- Flat NUT- Hex ~! SHIELD- Muffler HANDLE BAR TANK- Oil TUBING- (9') TUBING (4 3/4') FINDER- Oil VALVE- Check FITTING- Oil line CAP-Oil GASKET- Cap TANK- Fuel FIL TEA- Fuel LINE- Fuel (5 1/2') VALVE- Check CAP- Fuel GASKET- Cap STARTER HOUSING ASSY.

LOCK- Trigger STOP- Chain SCREW- Torx, taptite.

HOUSING- Engine TAPE DECAL DECAL (International Only) SCREW- Pan, plastite (#10-16 X 3/4') COVER- Handle SCREW- Pan plastite (#6-3/8') ROD- Throttle COVER- Air filter TRIGGER Stampato negli Stati Uniti PJ'N 18663įIGURE 1 FIGURE 1 ABBILDUNG 1 FIGURA 1 FIGURA 1 Turn the screw to the left and note the engine performance.®PARTS LIST 0 LISTE DE PIECES 0 TEILELISTE 0 LISTA DE PIEZAS 8 ELENCO DELLE PARTI Set the high speed screw by adjusting the screw marked "H." Pull the trigger so that the throttle opens as wide as possible.

#HOMELITE SUPER XL AUTOMATIC CARBURTER PDF#

Bookmark File PDF Homelite Textron Chainsaw Manual SystemPart 1 10 Chainsaw Fixer-up, Homelite XL-12 Homelite Super 2 Chainsaw - Carburetor Rebuild and Tuneup Homelite Chainsaw Wont Run. Set the High-Speed Screw Adjust the Homelite chainsaw carburetor by turning the high- and low-speed screws as needed. Super XL Chainsaw Bobs Homelite XL Automatic Oiler Repair Fixing a homelite chainsaw Homelite Super 2 Chainsaw Chain Oiling /48. Go back to step (4) and reset the idle speed.Begin by checking the saw's air filter.Before you start the saw, locate a small flat-bladed screwdriver.Place your left hand on the handle on top of the saw.Īlso asked, how do you adjust a chainsaw carburetor?.Locate the two handles on the saw, the top and rear one. Plug the male end of the extension cord into a power outlet.Fill the oil reservoir with chain saw lubricant. Open the oil reservoir cap on top of the chainsaw.

#HOMELITE SUPER XL AUTOMATIC CARBURTER HOW TO#

Turn the screw to the left and note the engine performance.Īlso know, how do you adjust the carburetor on a Homelite Super XL?Ĭhanging the Carburetor Setting Turn the idle-speed screw counterclockwise, or to the left, in one-quarter turn increments until the engine speed reduces, the saw idles smoothly and the chain no longer turns.īeside above, how do you start a Homelite 3514c chainsaw? How to Start a Homelite Chainsaw Adjust the Homelite chainsaw carburetor by turning the high- and low-speed screws as needed.